How to disconnect the washing machine If you replace an old washing machine. You will need to remove it first in order to replace the new one. This ca
How to disconnect the washing machine If you replace an old washing machine. You will need to remove it first in order to replace the new one. This can be a challenge, not just because it is difficult to wash. People can get services Washing Machine Installation in Dubai.
Disconnect the machine from water and power supply
To begin with, turn off the water supply to the clothes washer. The pressure in the water cords should rise immediately. So be prepared to place a bucket or cloth under the pipes. Before blocking them. Then, he pulls out an electric washing machine. When you are done with that, you will be ready to remove it from its place
Remove the machine from the path
You will need someone to help you with this because the washing machines are very heavy. If you are working alone, do not try to lift it yourself. Instead, move one side forward, and do the same on the other. Pull the machine forward while trying not to apply pressure to the drainage hose. Now you must have enough space to move on to the next step.
Remove the drainage pipe
Behind the washer is a water pipe. You will need to unlock the screws on the counter against the clock until they open. There will probably be water left in the hose, so fix the bucket. If the washing machine is old, removing the tube can be difficult. In this case, use two lumps to loosen the bonds. Remove the pipes from the wall and back of the washing machine.
Remove the drain hose
The hose drain is a little hard. Depending on your plumbing setup, it can be connected to a sink, floor drain, or wall mounted. Just follow where it leads and pull it out like other pipes. This hose can contain the remaining water. So, fix it again with a bucket.
Prepare to move
Moving a washing machine is a serious business, and you will need more tools than you need to install. First, you must protect the drum with special travel bolts to protect it from movement during transport. Insert bolts according to the production manual. Pipes and power cord should be securely installed in the machine. You will also need work gloves, lifting straps and someone to help you grow the machine.
How to install a washing machine
Now that you have a good location, it is time to install the washing machine inside. So, here’s how to install:
Connect the water pipe
To do this, you must attach the hose to the back of the washing machine and securely twist it. The other end of the tube should be connected to a water pipe. You do not need special tools for this; your hands are enough.
Bring a new washing machine
Moving a washing machine alone can be a big challenge, so we recommend that you hold a few friends. You will need to put a washer on the dolly to bring it to its original location. Place pieces of cardboard on the floor, so you don’t scratch the floor with a doll.
Remove the travel bolts
Now, you need to remove the travel bolts. If you do not, the bolts will interfere with the operation of the washing machine, causing excessive noise and internal damage to the drum.
The bolts are located on the back of your washing machine. Usually, there are three or 4 of them, locked in wire on your equipment. If you have trouble finding bolts, just look at the production manual.
Use a pliers or a spanner. Once you have removed the bolts, do not discard them, as you may need to use them for transport purposes.
Connect the drainage pipe
Ideally, the washing machine will sit in the kitchen next to the sink. Your sink should have a waste connection connected to the bottom. This is where you have to connect the drainage pipe. If you are installing a drainage pipe for the first time, remove the stops before installing the sewer pipe. The pipe should bend downwards. Fix it with the plastic handle provided by your washing machine.
In some cases, you can attach it to a drain on the floor, or you can use a standpipe if no extraction points are available. If you are using a standpipe, you will need one that is wider than the pipe. Remember that the standpipe should not be less than 30 cm high.
Start the test cycle
Once the pipes are connected. The water supply is turned on and you connect the washing machine to the electrical socket, it is time to do the testing. Load the washer by washing and inspecting it. Ensure there are no holes all through the framework. If there is a leak, you may need to tighten the pipes.
How to Keep a Washing Machine
Now you have a brand new washer that works perfectly for you for at least ten years. With the right adjustment, you can easily extend that time.
Check the drainage pipes
The most common cause of leak hose damage. To prevent this, it is a good idea to check the equipment every few months. If you see signs of damage, you will need to install some new pipes.
Turn off the washing machine valve
Turn off the water supply in the washing machine whenever you are away from home for a long time. By doing this, there will be less pressure on the intestinal tract and it will reduce aging.
Install the washer exhaust pan
A washer discharge pan is a pan that you put under the washing machine, which is also connected to the drain. In the event of a leak, instead of keeping the large duck on the floor. The pan will drain the water and save you from serious water damage.
Do not overload the washing machine
Overloading the washing machine and washing machine can cause damage. Also, be sure to leave the door open after bathing. If you have a problem with the smell of the drum after washing your washing machine, leave the door open to help with ventilation.
Clean the interior and distribution areas
Like any other machine, the washing machine needs to be cleaned again. You will have to wipe down the drum and especially clean the dispensers from any remaining detergent. You can also carry an empty load of hot water with 2 cups of white vinegar in a full cycle. In the middle of the washing cycle, add half a cup of cleaning. This will help in the fight against bad breath.